泰科納CELCON POM GC25A

金龍先生15916816001

郵       箱：1362174071@qq.com

洽談Q Q：1362174071

CELCON CF802 POM Specialty ESD (electrostatic dissipative) fuel compatable, general purpose material.
CELCON GB10 POM Glass Reinforced 10% glass bead, low warpage, has been replaced by Hostaform  C 9021 GV3/10
CELCON GB25 POM Glass Reinforced 25% glass bead filled for stiffness, low warpage
CELCON GC10 POM Glass Reinforced 10% glass fiber, has been replaced with Hostaform  C 9021 GV1/10
CELCON GC15 POM Glass Reinforced 15% glass fibers, coupled for improved stiffness
CELCON GC20 POM Glass Reinforced 20% glass fiber, has been replaced with Hostaform  C 9021 GV1/20
CELCON GC25A POM Glass Reinforced 25% glass fibers, coupled for improved stiffness, standard grade
CELCON GC25T POM Glass Reinforced 25% glass fibers, coupled for improved stiffness, high strength, improved fuel resistance
CELCON GC25TF POM Glass Reinforced 25% glass fibers, coupled for improved stiffness, high strength, fuel resistant, and high flow for thin parts
CELCON GC90UV POM UV Resistant Glass coupled, UV stabilized acetal copolymer.
CELCON LM90Z POM Specialty Laser markable, UV resistant to sunlight and artificial lighting
CELCON LU-02 POM UV Resistant UV resistant, reduced gloss
CELCON LW25-S2 POM Tribological Low wear/friction, silicone, low speed, high load, improved toughness
CELCON LW90 POM Tribological Low wear, high speed, low load
CELCON LW90-F2 POM Tribological Low wear/friction, low level PTFE modification, standard product
CELCON LW90FS-K POM Tribological Low wear based on silicone and high PTFE modification
CELCON LW90-S2 POM Tribological Low wear/friction, silicone modified, low speed, high load
CELCON LW90-SC POM Tribological Low friction, silcone concentrate for use with other Ticona products
CELCON M140 POM Unfilled General purpose, improved flow
CELCON M140-L1 POM Tribological General purpose, improved flow, minimize noise (squeak) when wearing against itself.
CELCON M15HP POM Unfilled Low flow, high strength and stiffness, improved impact
CELCON M25 POM Unfilled Imroved toughness, low flow
CELCON M25UV POM UV Resistant UV stabilized, improved toughness
CELCON M270 POM Unfilled General purpose, high flow, fast cycling
CELCON M270UV POM UV Resistant UV stabilized, high flow
CELCON M450 POM Unfilled Very high flow, fast cycling, has been replaced by Hostaform  C 52021
CELCON M50 POM Unfilled Intermediate grade for improved toughness
CELCON M90-07 POM Color Concentrate Color Concentrates
CELCON M90-34 POM Unfilled Standard unfilled appliance grade - improved stain resistance
CELCON M90-45H POM UV Resistant Formulated in custom colors for Toyota interior UV stabilized applications
CELCON M90-45XAP POM Specialty Low emission UV resistant grade based on Celcon M90  for interior automotive
CELCON M90AW POM Tribological Low wear, low noise, for low load, high speed applications
CELCON M90SW POM Tribological Low wear, low noise for high load, low speed applications.
CELCON M90 POM Unfilled General purpose, good optimization of properties
CELCON M90UV POM UV Resistant UV stabilized, general purpose grade
CELCON MC270 POM Mineral Reinforced Mineral coupled for reduced warpage, high flow
CELCON MC270-HM POM Mineral Reinforced Mineral coupled for reduced warpage, high modulus, high flow
CELCON MC90 POM Mineral Reinforced Mineral coupled for reduced warpage, general purpose grade
CELCON MC90-HM POM Mineral Reinforced Mineral coupled for reduced warpage, high modulus, moderate flow
CELCON MR25B POM Specialty improved media resistance, improved toughness
CELCON MR270B POM Specialty Improved media resistance to bleach with higher flow

  POM為白色一般不透明，著色性好， 比重1.41-1.43克/立方厘米，成型收縮率1.2-3.0%，成型溫度170-200℃ ，干燥條件80-90℃ 2小時。POM的長期耐熱性能不高，但短期可達到160℃，其中均聚POM短期耐熱比共聚POM高10℃以上，但長期耐熱共聚POM反而比均聚POM高10℃左右?？稍?40℃～100℃溫度范圍內長期使用。POM極易分解，分解溫度為240度。分解時有刺激性和腐蝕性氣體發生，故模具鋼材宜選用耐腐蝕性的材料制作。

（1）POM是結晶型塑料,密度為1.42g/cm3,它的鋼性很好,俗稱“賽鋼”.
　　（2）它具有耐疲勞、耐蠕變、耐磨、耐熱、耐沖擊等優良的性能,且摩擦系數小,自潤滑性好.
　?。?）POM不易吸濕,吸水率為0.22～0.25%,在潮濕的環境中尺寸穩定性好,其收縮率為2.1%(較大),注塑時尺寸較難控制,熱變形溫度為172℃
 
   POM強度、剛度高，彈性好，減磨耐磨性好。其力學性能優異，比強度可達50.5MPa，比剛度可達2650MPa，與金屬十分接近。POM的力學性能隨溫度變化小，共聚POM比均聚POM的變化稍大一點。POM的沖擊強度較高，但常規沖擊不及ABS和PC；POM對缺口敏感，有缺口可使沖擊強度下降90%之多。POM的疲勞強度十分突出，10交變載荷作用后，疲勞強度可達35MPa，而PA和PC僅為28MPa。POM的蠕變性與PA相似，在20℃、21MPa、3000h時僅為2.3%，而且受溫度的影響很小。POM的摩擦因數小，耐磨性好（POM>PA66>PA6>ABS>HPVC>PS>PC），極限PV值很大，自潤滑性好。POM制品對磨時，高載荷作用時易產生類似尖叫的噪聲。

   POM的電絕緣性較好，幾乎不受溫度和濕度的影響；介電常數和介電損耗在很寬的溫度、濕度和頻率范圍內變化很?。荒碗娀⌒詷O好，并可在高溫下保持。POM的介電強度與厚度有關，厚度0.127mm時為82.7kV/mm，厚度為1.88mm時為23.6kV/mm。
環境性能

POM不耐強堿和氧化劑，對烯酸及弱酸有一定的穩定性。POM的耐溶劑性良好，可耐烴類、醇類、醛類、醚類、汽油、潤滑油及弱堿等，并可在高溫下保持相當?shù)幕瘜W(xué)穩定性。吸水性小，尺寸穩定性好。
POM的耐候性不好，長期在紫外線作用下，力學性能下降，表面發生粉化和龜裂。

⒈增強POM
主要增強材料為玻璃纖維、玻璃球或碳纖維等，并且玻璃纖維常用，增強后的力學性能可提高2～3倍，熱變形溫度提高50℃以上。
⒉高潤滑POM
在POM中加入石墨、F4、二硫化鉬、潤滑油及低分子量PE等，可提高其潤滑性能。例如，在POM中加入5份F4，可降低摩擦因數60%，耐磨性提高1～2倍。再如，在POM中加入液體潤滑油，可大幅度提高耐磨性和極限PV值

POM又稱賽鋼、特鋼。它是聚合所得。POM-H，POM-K是高密度、高結晶度的熱塑性工程塑料。具有良好的物理、機械和化學性能，尤其是有優異的耐摩擦性能。

POM是一種表面光滑，有光澤的硬而致密的材料，淡黃或白色，可在-40- 100°C溫度范圍內長期使用。它的耐磨性和自潤滑性也比絕大多數工程塑料優越，又有良好的耐油，耐過氧化物性能。很不耐酸，不耐強堿和不耐紫外線的輻射。(加入U(xiǎn)V劑，能大大提高其耐紫外線等級）